TCP Keepalive HOWTO
Prev   Next

3. Using TCP keepalive under Linux

Linux has built-in support for keepalive. You need to enable TCP/IP networking in order to use it. You also need procfs support and sysctl support to be able to configure the kernel parameters at runtime.

The procedures involving keepalive use three user-driven variables:

tcp_keepalive_time

the interval between the last data packet sent (simple ACKs are not considered data) and the first keepalive probe; after the connection is marked to need keepalive, this counter is not used any further

tcp_keepalive_intvl

the interval between subsequential keepalive probes, regardless of what the connection has exchanged in the meantime

tcp_keepalive_probes

the number of unacknowledged probes to send before considering the connection dead and notifying the application layer

Remember that keepalive support, even if configured in the kernel, is not the default behavior in Linux. Programs must request keepalive control for their sockets using the setsockopt interface. There are relatively few programs implementing keepalive, but you can easily add keepalive support for most of them following the instructions explained later in this document.

3.1. Configuring the kernel

There are two ways to configure keepalive parameters inside the kernel via userspace commands:

  • procfs interface

  • sysctl interface

We mainly discuss how this is accomplished on the procfs interface because it's the most used, recommended and the easiest to understand. The sysctl interface, particularly regarding the   sysctl(2)syscall and not the  sysctl(8) tool, is only here for the purpose of background knowledge.

3.1.1. The procfs interface

This interface requires both sysctl and  procfs to be built into the kernel, and procfs mounted somewhere in the filesystem (usually on  /proc, as in the examples below). You can read the values for the actual parameters by "catting" files in  /proc/sys/net/ipv4/ directory:

  # cat /proc/sys/net/ipv4/tcp_keepalive_time
  7200

  # cat /proc/sys/net/ipv4/tcp_keepalive_intvl
  75

  # cat /proc/sys/net/ipv4/tcp_keepalive_probes
  9
        

The first two parameters are expressed in seconds, and the last is the pure number. This means that the keepalive routines wait for two hours (7200 secs) before sending the first keepalive probe, and then resend it every 75 seconds. If no ACK response is received for nine consecutive times, the connection is marked as broken.

Modifying this value is straightforward: you need to write new values into the files. Suppose you decide to configure the host so that keepalive starts after ten minutes of channel inactivity, and then send probes in intervals of one minute. Because of the high instability of our network trunk and the low value of the interval, suppose you also want to increase the number of probes to 20.

Here's how we would change the settings:

  # echo 600 > /proc/sys/net/ipv4/tcp_keepalive_time

  # echo 60 > /proc/sys/net/ipv4/tcp_keepalive_intvl

  # echo 20 > /proc/sys/net/ipv4/tcp_keepalive_probes
        

To be sure that all succeeds, recheck the files and confirm these new values are showing in place of the old ones.

Remember that procfs handles special files, and you cannot perform any sort of operation on them because they're just an interface within the kernel space, not real files, so try your scripts before using them, and try to use simple access methods as in the examples shown earlier.

You can access the interface through the   sysctl(8) tool, specifying what you want to read or write.

  # sysctl \
  > net.ipv4.tcp_keepalive_time \
  > net.ipv4.tcp_keepalive_intvl \
  > net.ipv4.tcp_keepalive_probes
  net.ipv4.tcp_keepalive_time = 7200
  net.ipv4.tcp_keepalive_intvl = 75
  net.ipv4.tcp_keepalive_probes = 9
        

Note that sysctl names are very close to  procfs paths. Write is performed using the -w switch of sysctl (8):

  # sysctl -w \
  > net.ipv4.tcp_keepalive_time=600 \
  > net.ipv4.tcp_keepalive_intvl=60 \
  > net.ipv4.tcp_keepalive_probes=20
  net.ipv4.tcp_keepalive_time = 600
  net.ipv4.tcp_keepalive_intvl = 60
  net.ipv4.tcp_keepalive_probes = 20
        

Note that sysctl (8) doesn't use sysctl(2) syscall, but reads and writes directly in the procfs subtree, so you will need procfs enabled in the kernel and mounted in the filesystem, just as you would if you directly accessed the files within the procfs interface.   Sysctl(8) is just a different way to do the same thing.

3.1.2. The sysctl interface

There is another way to access kernel variables: sysctl(2 ) syscall. It can be useful when you don't have procfs available because the communication with the kernel is performed directly via syscall and not through the procfs subtree. There is currently no program that wraps this syscall (remember that  sysctl(8) doesn't use it).

For more details about using  sysctl(2) refer to the manpage.

3.2. Making changes persistent to reboot

There are several ways to reconfigure your system every time it boots up. First, remember that every Linux distribution has its own set of init scripts called by init (8). The most common configurations include the /etc/rc.d/ directory, or the alternative, /etc/init.d/. In any case, you can set the parameters in any of the startup scripts, because keepalive rereads the values every time its procedures need them. So if you change the value of tcp_keepalive_intvl when the connection is still up, the kernel will use the new value going forward.

There are three spots where the initialization commands should logically be placed: the first is where your network is configured, the second is the rc.local script, usually included in all distributions, which is known as the place where user configuration setups are done. The third place may already exist in your system. Referring back to the sysctl (8) tool, you can see that the -pswitch loads settings from the  /etc/sysctl.conf configuration file. In many cases your init script already performs the sysctl -p (you can "grep" it in the configuration directory for confirmation), and so you just have to add the lines in  /etc/sysctl.conf to make them load at every boot. For more information about the syntax of  sysctl.conf(5), refer to the manpage.


Prev Home Next
TCP keepalive overview   Programming applications

TCP keepalive under Linux的更多相关文章

  1. Using TCP keepalive under Linux

    Linux has built-in support for keepalive. You need to enable TCP/IP networking in order to use it. Y ...

  2. TCP keepalive

      2. TCP keepalive overview In order to understand what TCP keepalive (which we will just call keepa ...

  3. TCP Keepalive HOWTO

    TCP Keepalive HOWTO Fabio Busatto <fabio.busatto@sikurezza.org> 2007-05-04 Revision History Re ...

  4. 【转载】TCP保活(TCP keepalive)

    下图是我遇到tcp keepalive的例子: 以下为转载: TCP保活的缘起 双方建立交互的连接,但是并不是一直存在数据交互,有些连接会在数据交互完毕后,主动释放连接,而有些不会,那么在长时间无数据 ...

  5. TCP连接探测中的Keepalive和心跳包. 关键字: tcp keepalive, 心跳, 保活

    1. TCP保活的必要性 1) 很多防火墙等对于空闲socket自动关闭 2) 对于非正常断开, 服务器并不能检测到. 为了回收资源, 必须提供一种检测机制. 2. 导致TCP断连的因素 如果网络正常 ...

  6. tcp keepalive选项

    之前一直对tcp keepalive选项理解有误, 以为通过setsockopt函数设置SO_KEEPALIVE和相关参数后该socket则使用设置的keepalive相关参数 否则使用系统默认的:k ...

  7. 心跳机制tcp keepalive的讨论、应用及“断网”、&quot;断电&quot;检测的C代码实现(Windows环境下)

    版权声明:本文为博主原创文章,转载时请务必注明本文地址, 禁止用于任何商业用途, 否则会用法律维权. https://blog.csdn.net/stpeace/article/details/441 ...

  8. TCP keepalive overview

    2. TCP keepalive overview In order to understand what TCP keepalive (which we will just call keepali ...

  9. 配置开发支持高并发TCP连接的Linux应用程序全攻略

    http://blog.chinaunix.net/uid-20733992-id-3447120.html http://blog.chinaunix.net/space.php?uid=16480 ...

随机推荐

  1. 阿里无线前端性能优化指南 (Pt.1 加载优化)

    前言 阿里无线前端团队在过去一年对所负责业务进行了全面的性能优化.以下是我们根据实际经验总结的优化指南,希望对大家有所帮助. 第一部分仅包括数据加载期优化. 图片控制 对于网页特别是电商类页面来说,图 ...

  2. 第二章 NIO入门

    传统的同步阻塞式I/O编程 基于NIO的非阻塞编程 基于NIO2.0的异步非阻塞(AIO)编程 为什么要使用NIO编程 为什么选择Netty 第二章 NIO 入门 2.1 传统的BIO编程 2.1.1 ...

  3. ACM-ICPC国际大学生程序设计竞赛北京赛区(2016)网络赛 The Book List

    描述 The history of Peking University Library is as long as the history of Peking University. It was b ...

  4. php调用whois接口域名查询

    由两部分组成,一个index.php文件,一个whois的接口文件: <html> <head> <title>域名到期查询</title> <s ...

  5. CentOS6.7 用户

    1.添加普通用户[root@server ~]# useradd chenjiafa   //添加一个名为chenjiafa的用户[root@server ~]# passwd chenjiafa   ...

  6. Android应用程序更新并下载

    创建一个新类,名为UpdateManager,代码如下: package com.af.service; import java.io.BufferedReader; import java.io.F ...

  7. Java中对List&lt;E&gt;按E的属性排序的简单方法

    这是LeetCode上的题目56. Merge Intervals中需要用到的, 简单来说,定义了E为 /** * Definition for an interval. * public class ...

  8. Django 1.11.7学习,配置MySQL数据库(python3.5)

    1.链接MySQL数据库 a.导入pymysql包 import pymysql pymysql.install_as_MySQLdb() b.改变DATABASES参数 ENGINE : 指定数据库 ...

  9. 在浏览器端用es6,babel+browserify打包

    写得最清楚的是这个系列: 一个普通的写网页的人如何过渡到ES6 (一) 感觉比babel官网写得还清楚点. 看完这个才有点理解node原来不只是用来起express后端web server,更主要用途 ...

  10. crontab使用环境变量

    两种方式: 1)直接在crontab中定义变量,如: A=123 * * * * * echo $A > /tmp/a.txt 注意在定义变量时不能使用$引用其它变量,如下面的做法错误: A=1 ...